Price Information
| Cat No. | Plasmid Name | Availability | Add to cart |
|---|---|---|---|
| V012900 | pCP-Cre | In stock, 1 week for quality controls |
Buy one, get one free! |
Two tubes of lyophilized plasmid will be delivered, each tube is about 5µg.
Basic Vector Information
- Vector Name:
- pCP-Cre
- Antibiotic Resistance:
- Chloramphenicol
- Length:
- 8780 bp
- Type:
- Gene knockout
- Replication origin:
- pSC101 ori
- Host:
- E. coli
- Growth Strain(s):
- DH5a
- Growth Temperature:
- 30℃
pCP-Cre vector Map
Plasmid Protocol
1. Centrifuge at 5,000×g for 5 min.
2. Carefully open the tube and add 20 μl of sterile water to dissolve the DNA.
3. Close the tube and incubate for 10 minutes at room temperature.
4. Briefly vortex the tube and then do a quick spin to concentrate the liquid at the bottom. Speed is less than 5000×g.
5. Store the plasmid at -20 ℃.
6. The concentration of plasmid re-measurement sometimes differs from the nominal value, which may be due to the position of the lyophilized plasmid in the tube, the efficiency of the re-dissolution, the measurement bias, and adsorption on the wall of the tube, therefore, it is recommended to transform and extract the plasmid before using it
General Plasmid Transform Protocol
1. Take one 100μl of the competent cells and thaw it on ice for 10min, add 2μl of plasmid, then ice bath for 30min, then heat-shock it at 42℃ for 60s, do not stir, and then ice bath for 2min.
2. Add 900μl of LB liquid medium without antibiotics, and incubate at 37℃ for 45min (30℃ for 1-1.5 hours) with 180rpm shaking.
3. Centrifuge at 6000rpm for 5min, leave only 100μl of supernatant to resuspend the bacterial precipitate and spread it onto the target plasmid-resistant LB plate.
4. Invert the plate and incubate at 37℃ for 14h, or at 30℃ for 20h.
5. Pick a single colony into LB liquid medium, add the corresponding antibiotics, incubate at 220rpm for 14h, and extract the plasmid according to the experimental needs and the instructions of the plasmid extraction kit.
pCP-Cre vector Sequence
LOCUS V012900 8780 bp DNA circular SYN 01-JAN-1980
DEFINITION Exported.
ACCESSION V012900
VERSION V012900
KEYWORDS .
SOURCE synthetic DNA construct
ORGANISM synthetic DNA construct
.
REFERENCE 1 (bases 1 to 8780)
AUTHORS .
TITLE Direct Submission
FEATURES Location/Qualifiers
source 1..8780
/mol_type="other DNA"
/organism="synthetic DNA construct"
CDS complement(564..1220)
/label="CmR"
/note="chloramphenicol acetyltransferase"
promoter complement(1221..1323)
/label="cat promoter"
/note="promoter of the E. coli cat gene encoding
chloramphenicol acetyltransferase"
rep_origin 1875..2097
/label="pSC101 ori"
/note="low-copy replication origin that requires the Rep101
protein"
CDS 2145..3092
/label="Rep101(Ts)"
/note="temperature-sensitive version of the RepA protein
needed for replication with the pSC101 origin (Armstrong et
al., 1984)"
CDS complement(4016..4360)
/gene="mbeC"
/label="Mobilization protein MbeC"
/note="Mobilization protein MbeC from Escherichia coli.
Accession#: P13657"
CDS complement(4560..5417)
/label="AmpR"
/note="beta-lactamase"
promoter complement(5418..5522)
/label="AmpR promoter"
CDS complement(5800..6828)
/label="Cre"
/note="site-specific recombinase"
protein_bind complement(6854..6870)
/label="lac operator"
/note="The lac repressor binds to the lac operator to
inhibit transcription in E. coli. This inhibition can be
relieved by adding lactose or
isopropyl-beta-D-thiogalactopyranoside (IPTG)."
promoter complement(6878..6908)
/label="lac UV5 promoter"
/note="E. coli lac promoter with an 'up' mutation"
promoter 7219..7296
/label="lacI promoter"
CDS 7297..8376
/label="lacI"
/note="lac repressor"